Jun 20, 2024

Operating instructions for Punch Press

Leave a message

Mechanical work
Due to the poor lubrication of the punch, the friction resistance increases when the worktable moves. When the motor is driven, the worktable does not move forward, which causes the ball screw to produce elastic deformation, and stores the energy of the motor in the deformation. When the motor continues to drive, and the elastic force produced by the stored energy is greater than the static friction force, the punch table creeps forward, and moves like this again and again, resulting in the phenomenon of crawling. However, this is not the case, and a closer look at the lubrication of the rail surface can conclude that this is not the problem. The problem of punch crawling and vibration is a matter of speed. Since it is a matter of speed, it is necessary to find the speed ring, and the whole adjustment process of the speed of the punch is completed by the speed regulator.


The operation and monitoring of the CNC punch are all done in this CNC unit, which is the brain of the CNC punch. High machining accuracy and stable processing quality; Carry out multi-coordinate linkage, can process parts with complex shapes; When the processed parts are changed, generally only need to change the CNC program, which can save production preparation time; The bed itself has high precision and rigidity, and can choose a favorable processing amount and high productivity (generally 3~5 times that of ordinary machine tools). For speed-related problems, you can only look for the speed adjuster. Therefore, if you have a problem with the vibration of the punch press, you should also look for the speed regulator. Fault in the speed regulator can be found in the following places: a given signal, a feedback signal, and the speed regulator itself.


Because the vibration frequency of the punch is in a certain ratio to the speed of the motor, the first thing to check is whether the motor is faulty, check its carbon brush, commutator surface condition, and mechanical vibration, and check the lubrication of the ball bearing. If there are no problems, check the tachogenerator. Tachogenerators are generally DC.


The punch tachometer generator is a small permanent magnet DC generator, and its output voltage should be proportional to the speed, that is, the output voltage and the speed are linear. As long as the speed is constant, its output voltage waveform should be a straight line, but due to the influence of cogging and commutator commutation, a small intersection variable is attached to this straight line. For this reason, a filter circuit is added to the speed feedback circuit, and this filter circuit is to weaken the AC component attached to the voltage.
The punch feedback signal is exactly the same as the given signal for the regulator. Therefore, the fluctuation of the feedback signal will inevitably cause the speed regulator to adjust in the opposite direction, which will cause the vibration of the punch. When this happens, it is very easy to deal with, and as long as the back cover of the motor is removed, the commutator of the tachogenerator is exposed. At this time, there is no need to do any disassembly, just use a sharp hook, carefully hook each groove, and then use fine sandpaper to polish the hooked burrs, wipe the surface of the fairing sheet with anhydrous alcohol, and then put a charcoal brush. Special attention here is to use a sharp hook to hook the notch between the pieces, do not touch the winding, because the winding wire is very thin, once it is broken, it cannot be repaired, only to replace the winding. Again, don't wipe it with watery alcohol, so that the insulation resistance drops and can't be dried, which will delay the repair period.


A closed-loop system may also cause system oscillation due to poor parameter setting, but the way to eliminate this oscillation is to reduce its amplification, adjust RV1 in the FANUC system, and rotate in the direction of the clock, then it can be seen that it will immediately become significantly better, but because the range of RV1 adjustment potentiometer is relatively small, sometimes it cannot be adjusted, and only the short-circuit rod can be changed, that is, the feedback resistance value is cut off, and the magnification of the entire regulator can be reduced.


Mechanical use
The press should comply with the following procedures for punching and forming. When more than two people operate, someone should be assigned to drive, and attention should be paid to good coordination. Before leaving work, the mold should be dropped, the power supply should be disconnected, and the necessary cleaning should be carried out. Transmission components exposed to the outside of the press must be fitted with a protective cover, and it is forbidden to drive or test the car with the protective cover removed. If necessary, the empty car can be tested. The installation mold must open the slider to the bottom dead center, and the closing height must be correct, and the eccentric load must be avoided as much as possible; The mold must be fastened firmly and checked by pressure test.


Attention should be concentrated in the work, and it is strictly forbidden to put hands and tools and other objects into the danger zone (see item 4 of the safety production regulations) If you find that the press is running abnormally or has abnormal sounds, (such as continuous hitting sound, bursting sound), you should stop feeding and check the cause. If the rotating parts are loose, the control device is out of order, (see introduction) every time a workpiece is punched, the hands or feet must leave the button or pedal to prevent misoperation. Before work, check whether the punch guard is complete and whether the flywheel runs smoothly; Whether there is protection on the upper part and both sides of the foot pedal device, and whether the operation is reliable and flexible; and remove objects that hinder operation in the workplace.


The punching force must be verified, and overload operation is strictly prohibited. When installing and disassembling the mold, the power supply must be cut off first. The mold installation must be firm and reliable. When adjusting the height of the car, it is carried out gradually by manual or dynamic method, and it is forbidden to connect to the car until the adjustment is confirmed. When operating, it is necessary to concentrate on thinking, it is strictly forbidden to talk and do at the same time, and cooperate with each other to ensure safe operation. Generally, it is forbidden for more than two people to operate the punch at the same time. If necessary, there must be a dedicated person to direct and be responsible for the operation of the foot pedal. It is strictly forbidden to feed and discharge any part of the body in the work, and there should be special tools for feeding and unloading the mold.


It is forbidden to punch the interlayer feed, and the second feed can only be carried out after the previous punch or the remaining material must be removed. The installation of the mold must be checked regularly, and if there is looseness or slippage, it should be adjusted in time. Before the knife edge is worn to the point that the burr exceeds the standard, the knife edge should be repaired in time. When disassembling the mold, it must be done in the clamping state. Take care of stamping equipment, dies, tools, gauges and instruments. After the work is completed, the mold and punch should be wiped clean and ready. In the formal punching process, because the static difference rate of the main motor changes with different loads, when punching different parts, the electromagnetic counter arranged on the control board can be used to correct the rotational speed.

 

Send Inquiry